View P0102BA1AA3_7179987.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

november 2008 rev 1 1/11 11 p010xx sensitive standard scrs up to 0.8 a features i t(rms) up to 0.8 a v drm /v rrm 100, 200, 400 and 600 v i gt from 5 to 200 a description thanks to highly sensitive triggering levels, the p010xx scr series is suitable for all applications where available gate current is limited, such as ground fault circuit interruptors, pilot circuits in solid state relays, stand-by mode power supplies, smoke and alarm detectors. available in through-hole or surface mount packages, the voltage capability of this series has been upgraded since its introduction and is now available up to 600 v. a k g to-92 (p010xxa) sot-223 (p0102xn) a k g a a k g a k g sot23-3l (p010xxl) table 1. device summary order code voltage sensitivity package packing mode 100 v 200 v 400 v 600 v p0102aa 1aa3 x 200 a to-92 bulk p0102aa 5al3 x 200 a to-92 tape and reel 13 inch p0102al 5aa4 x 200 a sot23-3l tape and reel 7 inch p0102ba 1aa3 x 200 a to-92 bulk p0102bl 5aa4 x 200 a sot23-3l tape and reel 7 inch p0102da 1aa3 x 200 a to-92 bulk p0102da 2al3 x 200 a to-92 ammopack p0102da 5al3 x 200 a to-92 tape and reel 13 inch p0102dn 5aa4 x x 200 a sot-223 tape and reel 7 inch p0102ma 1aa3 x 200 a to-92 bulk p0102mn 5aa4 x 200 a sot-223 tape and reel 7 inch p0109al 5aa4 x 1 a sot23-3l tape and reel 7 inch p0109da 1aa3 x 1 a to-92 bulk p0109da 5al3 x 1 a to-92 tape and reel 13 inch www.st.com
characteristics p010xx 2/11 1 characteristics table 2. absolute ratings (limiting values) p010xxa and p010xxn symbol parameter value unit i t(rms) rms on-state current (180 conduction angle) to-92 t l = 55 c 0.8 a sot-223 t amb = 70 c it (av) average on-state current (180 conduction angle) to-92 t l = 55 c 0.5 a sot-223 t amb = 70 c i tsm non repetitive surge peak on-state current t p = 8.3 ms t j = 25 c 8 a t p = 10 ms 7 i 2 ti 2 t value for fusing t p = 10 ms t j = 25 c 0.24 a 2 s di/dt critical rate of rise of on-state current i g = 2 x i gt , t r 100 ns f = 60 hz t j = 125 c 50 a/s i gm peak gate current t p = 20 s t j = 125 c 1 a p g(av) average gate power dissipation t j = 125 c 0.1 w t stg t j storage junction temperature range operating junction temperature range - 40 to + 150 - 40 to + 125 c table 3. absolute ratings (limiting values) p010xxl symbol parameter value unit i t(rms) rms on-state current (180 conduction angle) t amb = 36 c 0.25 a it (av) average on-state current (180 conduction angle) t amb = 36 c 0.16 a i tsm non repetitive surge peak on-state current t p = 8.3 ms t j = 25 c 7 a t p = 10 ms 6 i 2 ti 2 t value for fusing t p = 10 ms t j = 25 c 0.18 a 2 s di/dt critical rate of rise of on-state current i g = 2 x i gt , t r 100 ns f = 60 hz t j = 125 c 50 a/s i gm peak gate current t p = 20 s t j = 125 c 0.5 a p g(av) average gate power dissipation t j = 125 c 0.02 w t stg t j storage junction temperature range operating junction temperature range - 40 to + 150 - 40 to + 125 c
p010xx characteristics 3/11 table 4. electrical characteristics (1) p010xxa and p010xxn symbol test conditions value unit i gt v d = 12 v r l = 140 min. - a max. 200 v gt max. 0.8 v v gd v d = v drm r l = 3.3 k r gk = 1 k t j = 125 c min. 0.1 v v rg i rg = 10 a min. 8 v i h i t = 50 ma r gk = 1 k max. 5 ma i l i g = 1 ma r gk = 1 k max. 6 ma dv/dt v d = 67 % v drm r gk = 1 k t j = 125 c min. 75 v/s v tm i tm = 1.6 a tp = 380 s t j = 25 c max. 1.95 v v t0 threshold voltage t j = 125 c max. 0.95 v r d dynamic resistance t j = 125 c max. 600 m i drm i rrm v drm = v rrm = 400 v r gk = 1 k t j = 25 c max. 1 a v drm = v rrm = 600 v r gk = 1 k 10 v drm = v rrm r gk = 1 k t j = 125 c 100 1. t j = 25 c, unless otherwise specified table 5. electrical characteristics (1) p010xxl symbol test conditions p0102xl p0109al unit i gt v d = 12 v r l = 140 max. 200 1 a v gt max. 0.8 v v gd v d = v drm r l = 3.3 k r gk = 1 k t j = 125 c min. 0.1 v v rg i rg = 10 a min. 8 v i h i t = 50 ma r gk = 1 k max. 6 ma i l i g = 1 ma r gk = 1 k max. 7 ma dv/dt v d = 67 % v drm r gk = 1 k t j = 125 c min. 200 100 v/s v tm i tm = 0.4 a tp = 380 s t j = 25 c max. 1.7 v v t0 threshold voltage t j = 125 c max. 1.0 v r d dynamic resistance t j = 125 c max. 1000 m i drm i rrm v drm = v rrm t j = 25 c max. 1 a t j = 125 c 100 1. t j = 25 c, unless otherwise specified
characteristics p010xx 4/11 table 6. thermal resistance symbol parameter maximum unit r th(j-a) junction to case (dc) to-92 80 c/w r th(j-t) junction to tab (dc) sot-223 30 c/w r th(j-a) junction to ambient (dc) to-92 150 c/w s (1) = 5 cm 2 sot-223 60 r th(j-a) junction to ambient (mounted on fr4 with recommended pad layout) sot23-3l 400 c/w 1. s = copper surface under tab. figure 1. maximum average power dissipation vs. average on-state current p010xxa and p010xxn figure 2. maximum average power dissipation vs. average on-state current p010xxl 0 . 00 .1 0 .2 0 . 30 .4 0 . 50 . 6 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 p(w) = 180 360 i (a) t(av) 0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.20 0.22 0.24 0.26 0.28 0.30 p(w) i (a) t(av) = 180 360 figure 3. average and dc on-state current vs. lead temperature p010xxa and p010xxn figure 4. average and dc on-state current vs. ambient temperature p010xxa and p010xxn 0 25 50 75 100 125 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 i (a) t(av) t (c) lead = 180 (sot-223) = 180 (to-92) d.c. (sot-223) d.c. (to-92) 0 25 50 75 100 125 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 i (a) t(av) t (c) amb = 180 (sot-223) = 180 (to-92) d.c. (sot-223) d.c. (to-92) device mounted on fr4 with recomended pad layout for sot-223
p010xx characteristics 5/11 figure 5. average and dc on-state current vs. case temperature p010xxl figure 6. relative variation of thermal impedance junction to ambient vs. pulse duration 0 25 50 75 100 125 0.00 0.05 0.10 0.15 0.20 0.25 0.30 i (a) t(av) t (c) case = 180 d.c. 1e-2 1e-1 1e+0 1e+1 1e+2 5e+2 0.01 0.10 1.00 k=[z /r th(j-a) th(j-a) ] t (s) p sot-223 to-92 sot23-3l figure 7. relative variation of gate trigger, holding, and latching currents vs. junction temperature figure 8. relative variation of holding current vs. gate-cathode resistance -40 -20 0 20 40 60 80 100 120 140 0 1 2 3 4 5 6 t (c) j i,i,i[t] / gt h l j i ,i ,i [t =25c] gt h l j i gt i h & i r = 1k l gk typical values 1e-2 1e-1 1e+0 1e+ 1 0 2 4 6 8 10 12 14 16 18 20 r(k) gk i [r ] / i [ =1k ] hgk h r gk t j = 25c typical values figure 9. relative variation of dv/dt immunity vs. gate-cathode resistance figure 10. relative variation of dv/dt immunity vs. gate-cathode capacitance 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0.1 1.0 10.0 r(k) gk dv/dt[r ] / dv/dt[ =1k ] gk r gk t j = 125c v = 0.67 x v d drm typical values 01234567 0 2 4 6 8 10 c (nf) gk dv/dt[c ] / dv/dt[ =1k ] gk r gk t v = 0.67 x v = 125c r = 1k d drm gk j typical values
characteristics p010xx 6/11 figure 11. surge peak on-state current versus number of cycles figure 12. non-repetitive surge peak on-state current and corresponding value of i2t i (a) tsm 1 10 100 1000 0 1 2 3 4 5 6 7 8 number of cycles non repetitive t initial=25c j repetitive t =25c amb t =10ms p one cycle i (a), i t (a s) tsm 22 100.0 10.0 1.0 0.1 0.01 0.10 1.00 10.00 t initial = 25c j i t 2 i tsm t (ms) p for a sinusoidal pulse with width tp < 10 ms figure 13. on-state characteristics p010xxa, p010xxn figure 14. on-state characteristics p010xxl i (a) tm 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 1e+1 1e+0 1e-1 1e-2 v =0.95v r =600m t max.: j t0 d v (v) tm t j =max t =25c j maximum values 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 1e-2 1e-1 1e+0 1e+1 i (a) tm v (v) tm t j =max t =25c j v =1.0v r=1 t max.: j t0 d maximum values figure 15. thermal resistance junction to ambient vs. copper surface under tab p010xxn figure 16. thermal resistance junction to ambient vs copper surface under tab p010xxl 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 130 120 110 100 90 80 70 60 50 40 30 20 10 0 s(cm2) r (c/w) th(j-a) epoxy printed circuit board fr4, copper thickness = 35 m 0 102030405060708090100 0 100 200 300 400 500 s(cm2) r (c/w) th(j-a) epoxy printed circuit board fr4, copper thickness = 35 m
p010xx ordering information scheme 7/11 2 ordering information scheme figure 17. ordering information scheme 3 package information epoxy meets ul94, v0 in order to meet environmental requirements, st offers these devices in ecopack ? packages. these packages have a lead-free second level interconnect. the category of second level interconnect is marked on the package and on the inner box label, in compliance with jedec standard jesd97. the maximum ratings related to soldering conditions are also marked on the inner box label. ecopack is an st trademark. ecopack specifications are available at www.st.com . sensitive scr series sensitivity voltage package packing mode current 01 up to 0.8 a 02 = 200 a 09 = 1 a a = 100 v b = 200 v d = 400 v m = 600 v a = to-92 l = sot23-3l n = sot-223 1aa3 = bulk 2al3 = ammopack 5al3 = tape and reel 13 inch 5aa4 = tape and reel 7 inch blank p 01 0x x x xaxx table 7. to-92 dimensions ref dimensions millimeters inches min typ max min typ max a 1.35 0.053 b 4.70 0.185 c 2.54 0.100 d 4.40 0.173 e 12.70 0.500 f 3.70 0.146 a 0.50 0.019 a f c b a de
package information p010xx 8/11 figure 18. footprint (dimensions in mm) table 8. sot-223 dimensions ref. dimensions millimeters inches min. typ. max. min. typ. max. a 1.80 0.071 a1 0.02 0.001 b 0.60 0.70 0.80 0.024 0.027 0.031 b1 2.90 3.00 3.10 0.114 0.118 0.122 c 0.24 0.26 0.32 0.009 0.010 0.013 d 6.30 6.50 6.70 0.248 0.256 0.264 e2.3 0.090 e1 4.6 0.181 e 3.30 3.50 3.70 0.130 0.138 0.146 h 6.70 7.00 7.30 0.264 0.276 0.287 v10 max a a1 e1 d b1 h e e 12 4 3 b v c 3.25 1.32 7.80 5.16 1.32 2.30 0.95
p010xx package information 9/11 figure 19. footprint (dimensions in mm) table 9. sot23-3l dimensions ref. dimensions millimeters inches min. max. min. max. a 0.89 1.4 0.035 0.055 a1 0 0.1 0 0.004 b 0.3 0.51 0.012 0.02 c 0.085 0.18 0.003 0.007 d 2.75 3.04 0.108 0.12 e 0.85 1.05 0.033 0.041 e1 1.7 2.1 0.067 0.083 e 1.2 1.6 0.047 0.063 h 2.1 2.75 0.083 0.108 l 0.6 typ. 0.024 typ. s 0.35 0.65 0.014 0.026 a1 a l h b e d e e1 s c 0.95 0.61 1.26 3.25 0.73
ordering information p010xx 10/11 4 ordering information 5 revision history table 10. ordering information order code marking package weight base qty packing mode p0102aa 1aa3 p0102 aa to-92 0.2 g 2500 bulk p0102aa 5al3 p0102 aa to-92 0.2 g 2000 tape and reel 13 inch p0102al 5aa4 p2a sot23-3l 0.01 g 3000 tape and reel 7 inch p0102ba 1aa3 p0102 ba to-92 0.2 g 1000 bulk p0102bl 5aa4 p2b sot23-3l 0.01 g 3000 tape and reel 7 inch p0102da 1aa3 p0102 da to-92 0.2 g 2500 bulk p0102da 2al3 p0102 da to-92 0.2 g 2000 ammopack p0102da 5al3 p0102 da to-92 0.2 g 2000 tape and reel 13 inch p0102dn 5aa4 p2d sot-223 0.11 g 3000 tape and reel 7 inch p0102ma 1aa3 p0102 ma to-92 0.2 g 2500 bulk p0102mn 5aa4 p2m sot-223 0.11 g 2000 tape and reel 7 inch p0109al 5aa4 p9a sot23-3l 0.01 g 3000 tape and reel 7 inch p0109da 1aa3 p0109 da to-92 0.2 g 2500 bulk p0109da 5al3 p0109 da to-92 0.2 g 2000 tape and reel 13 inch table 11. document revision history date revision description of changes 24-nov-2008 1 first issue.
p010xx 11/11 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a particular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by an authorized st representative, st products are not recommended, authorized or warranted for use in military, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or register ed trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2008 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of P0102BA1AA3

	To Download P0102BA1AA3 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .